Pressure Balance Trim with Integrated Volume Control Installation Instructions
- Last updated
-
-
Save as PDF
For Model(s): ARB6400, ARB7400, AC600, AC700, A6400, A7400, U.6700, 0.7700,U.6000, U.7000, A6200, A7200, BA600, & BA700
Shut water supply to the faucet off: Important: Turn off the water supply at the faucet before starting. You can either turn off the main supply to the house or close the shut-off valves if the faucet is equipped with them. Then open the faucet again to empty it of residual water. Failure to do so could result in flooding or injury.
 |
|
POS.
|
DESCRIPTION
|
CODE
|
| 1 |
Diverter rod |
ZZ 95025 0 |
| 1-1 |
Diverter knob |
ZZ 94644 0 |
| 2 |
Faceplate with diverter |
ZZ 95026 0 |
| 2 |
Faceplate without diverter |
ZZ 95027 0 |
| 2 |
Faceplate with diverter - modern |
ZZ 95074 0 |
| 2 |
Faceplate without diverter - modern |
ZZ 95075 0 |
| 2-1 |
Gasket for faceplate |
ZZ 9502 0 |
| 3 |
Dome cap |
ZZ 95029 0 |
| 4 |
Cover ring |
ZZ 95030 0 |
| 5 |
Cartridge rod adaptor |
ZZ 95031 0 |
| 5-1 |
Set screw M.5x6 |
ZZ 94063 0 |
| 6 |
Lever escutcheon |
ZZ 95032 0 |
| 7 |
Lever extension |
ZZ 92671 0 |
| 11 |
Screw M.3,5x30 |
ZZ 95078 0 |
| 12 |
Extension |
ZZ 93497 0 |
| 13 |
Modern dome cap |
ZZ 95077 0 |
|
Trim Parts Instructions
- Mount Sealing Gasket (2-1) into Faceplate (2)
- Thread on Diverter Rod (1) if applicable
- Remove the faceplate nut (R945440) from the valve and install faceplate (2)
- Thread on faceplate nut (R945440). Please note: faceplate nut is provided on the rough valve not with the trim
- Use Cover Sleeve (3) as a wrench to tighten the faceplate nut into place
- Slide Trim Ring (4) onto Cover Sleeve (3) to hide the edge of the Faceplate nut (R945440). Please note: 0-ring on (4) is installed on the inner diameter of the Trim Ring (4)
- Install Cartridge Interface (5) onto the stem of the cartridge. Use of 2.5 MM Allen key is needed
- Slip Trim cover (6) against cartridge interface (5)
- Install Handle Spacer (7) and tighten screw (5-1)
- Install lever or cross handle onto Handle Spacer (7).Use of 2.5 MM Allen key is needed
- Thread on Diverter button (1-1)
- Test. Adjust if necessary.
- 3/8" Extension Nut available; part # R945440/2
- Extended stem available; part # 30134
|
| ITEM # |
PART # |
DESCRIPTION |
| 1 |
1.111 |
DIVERTER ONLY, PRESSURE BALANCE VALVE-QTY 1 |
| 2 |
10351 |
SLEEVE, CARTRIDGE PRESSURE BALANCE-QTY 1 |
| 3 |
10352 |
NUT, PRESSURE BALANCE VALVE-QTY 1 |
| 4 |
10715 |
CARTRIDGE, PRESSURE BALANCE 40MM-QTY 1 |
| Sa |
10592 |
BODY,PRESSURE BALANCE FOUR X 112"NPT-QTY 1 |
| Sb |
10807 |
BODY, PRESSURE BALANCE FOR DIVERTER-QTY 1 |
| 6 |
10810 |
CARTRIDGE BASE EXTENSION FOR HK-40-QTY 1 |
| 7 |
2-075 |
SHUTOFF VALVE. PRESSURE BALANCE-QTY 2 |
| 8 |
90031 |
0-RING, 1-3/4"10 X 1-7/8"00 X 1/16"THK, AS-568-031-QTY 2 |
| 9 |
R945440 |
FACEPLATE NUT, PRESSURE BALANCE-QTY 1 |
|
SPECIFICATIONS DETAILS:
5-6 GPM @ 60 PSI
- Unique volume control with pressure balance
- Integrated stops
- Min. Wild depth: 2"
- Max. Instal depth: 3"
- If PEX is utilized, oversize the supply line to 3/4" for full flow capacity
- Install any tub spout 18" min. from the diverter or valve outlet
- If using R2012D with a wall mounted tub spout with integrated diverter such as RT8000 diverter tub spout, a twin ell will be needed by the installer.The top outlet will be plugged.
|
Contact Us:
Canadian Consumers: Email or Call 1-866-473-8442
U.S. Consumers: Email or Call 1-800-777-9762
|
 |
