Top or Side Handle Pull-Out Kitchen Faucet Install Instructions

Last updated
Save as PDF

R77V3_Installation_Instructions.pdf

Instructions

Note: This mixer fits a maximum bench thickness of 2-1/2"and has a 90^o spout arc.

Flush pipe work to ensure it is free from debris. Shut water supply to the faucet off: Important: Turn off the water supply at the faucet before starting. You can either turn off the main supply to the house or close the shut-off valves if the faucet is equipped with them. Then open the faucet again to empty it of residual water. Failure to do so could result in flooding or injury.
Cut a mounting hole 1-3/8" diameter in the desired position for the faucet ensuring there is 30 inches clear vertical space below the hole for free movement of the hose. Check that there is 5/8" of flat surface around the edge of the hole, and that the handset is able to reach where required.
Remove faucet from packaging. Unscrew mounting nut and remove washer from threaded nipple mount. Ensure 'O' ring is sitting in the groove at base of the escutcheon and lower faucet through mounting hole.
From underneath the bench, slide the washer gasket, horseshoe washer and mounting nut over connection pipes and tighten onto threaded nipple mount.
Connect the inlet hoses to the water supply (hot inlet indicated with a red tape indicator). Ensure that the hose supply lines do not obstruct the travel of the sprayer hose.
Connect the nipple adaptor along with check valve adaptor to the bottom of the nipple mount. Then, connect the pull out spray hose. Ensure the adaptor containing the non-return valve is fitted, and make sure the sealing washer is in place by turning the nut on the check valve adaptor rather than the hose itself.
Remove handset from packaging, ensure the rubber washer is in place and tighten hose onto handset.
Remove hose counterweight from packaging and fit to hose approximately 23-5/8" below bench surface. Check travel of handset and reposition counterweight if necessary.
Turn on water supply and check for leaks. Test operation of handset by pressing button on top of handset to change from standard spray to shower spray settings by rotating the button on wand.

Adjustments Anti-Scald Ring:

An anti-scald ring is fitted to this mixer to limit the maximum movement of the handle when turned to the "HOT" position.

Ex factory the cartridge is set to the maximum HOT water flow.

Remove handle by loosening set screw through access hole under red/blue indicator with Hexagon Key provided. Grip cover sleeve and lift up to remove.
Lift the anti-scald ring sufficiently to disengage. Turn anti-clockwise and replace until the desired maximum temperature is obtained. Each notch on the ring gives a temperature change of approximately 3.5^oF.
Replace cover sleeve and handle.

Care and Maintenance

We recommend occasional cleaning with warm soapy water followed by polishing with a soft cloth to keep the plated finish in good condition. Do not use abrasive liquids, powders or pads to clean the product. You will damage the finish and void the warranty.

Guarantee to the Consumer:

Warranty

Rohl LLC warrants this product to be free from defects in materials or workmanship for as long as the original consumer purchaser owns their home.

Rohl LLC will provide free of charge, at its option, replacement part(s) or product (or a comparable alternative product) to replace those which have proven defective in materials or workmanship. We will not assume liability for labor expended or damages accruing from use of the material purchased from us. If material is defective, the limit of damage is the price of the defective material.

Proof of purchase (original sales receipt) from the original consumer purchaser must be made available to Rohl LLC for all warranty claims. The warranty is not transferable and is extended solely to the original purchaser of the product.

Warranty Exclusion

This warranty is for normal domestic use only and excludes defect or injury caused by or resulting from misuse, abuse or neglect, accidental damage or improper installation. The lifetime limited warranty does not apply to replacement of components where damage is caused by normal wear and tear.

Warranty will be invalid if:

A. The product has not been correctly installed (whether by a plumber, contractor, service provider or member of the purchaser's household) in accordance with the manufacturer's instructions.

B. The surface finish of the product has been damaged by use of unsuitable cleaning agents or improper materials, i.e. damage by agents containing acidic, corrosive, abrasive or alcohol-based substances or through scouring the surface by abrasive cloths.

C. Damage has occurred to component parts due to foreign materials in the water supply (e.g. stones, metal shavings). All water lines must be flushed clear of all debris prior to installing the product. It is strongly recommend that in areas where foreign materials may be present in the water supply, an inline filter be fitted on both the Hot and Cold inlets. This will ensure your warranty remains valid.

D. The product has been exposed to excessive high water temperature (above 80^o Celsius or 175^o Fahrenheit).

Parts Only Warranty

This warranty does not cover labor charges incurred and/or damage sustained in installation, repair or replacement, nor incidental or consequential damages.

Contact Us:

Canadian Consumers: Email or Call 1-866-473-8442

U.S. Consumers: Email or Call 1-800-777-9762